Tile Over Vinyl. We here at Country Custom Tile are asked frequently by Do- It- Yourselfers, Can I install tile over vinyl ? There is no simple yes or no answer. It can be done with the proper preparation and investigation into the condition of the vinyl and how well its bonded to the surface below. The sheet vinyl must be clean and free of dirt or other bond breakers. This is true of any surface to which you are trying to bond the tile. Mortar and adhesive manufacturers require clean surfaces for bonding. In order to get good solid bonding, the adhesives must be able to intimately contact both bonding surfaces (in this case the back of the tile and the vinyl). ![]() In the case that either of the surfaces are dirty with grit, oil, wax, or other bond inhibiting films, a good bond cannot be achieved due to the fact that the adhesive isn’t able to contact the necessary surfaces, physically or chemically. Because the vinyl often has a very smooth surface finish, scarification is required to enhance its bondability. Sanding or scarifying enhances the probability of strong physical bonding between the adhesive, tile, and the vinyl by providing more surface area on the vinyl. This greatly improves the chances for mechanical “locking” and better physical contact. Some of the no- wax floor finishes ( urethane coated) are intentionally very smooth so the floors maintain their shine. In these cases, scarifying will help create a better bonding surface. WARNING: If you are going to scarify or sand the floor prior to installing tile, it’s important to know if the vinyl contains asbestos. Tile & Stone Installation Systems Installing tile over sheet vinyl Frequently Asked Questions Can I install tile over sheet vinyl? While ceramic and porcelain tile. Laying Vinyl Over Ceramic. I found a great sale on some Armstrong urethane that I'd like to install. A good quality vinyl floor is thick enough to be. Install a Ceramic Tile Floor in the. there's a good chance that you'll have to install backer board over your vinyl to make the floor thicker and stiff enough. Flooring containing asbestos should definitely NOT be sanded! If you’re unsure, you can cut a small sample (only a small piece is generally needed a 1- inch by 1 inch) and have it tested at a local asbestos laboratory (found in the Yellow Pages) for a nominal fee if time permits. The health risks of sanding a floor containing asbestos has to do with the harmful airborne particles which will be generated. The sheet vinyl must be single layer only and well attached. It should not be perimeter glued (it often is!). In some cases a cushioning layer is installed underneath the vinyl or the vinyl sheet itself is cushion backed. For tiling purposes, this will allow too much movement in the system and may lead to a failure in the tile. Even if the tile and vinyl form a good bond together, if the vinyl isn’t secured to the surface or allows too much movement, the tile could fail. In addition, in the case of future repairs where one tile had to be replaced, removing a tile from a vinyl surface which is poorly bonded to the subfloor could lead to damage in adjacent grout and tile. ![]() The vinyl must be bonded using a full spread adhered system . This also provides stability in the vinyl as a substrate. A system which is only tacked at the perimeters will again allow too much movement. Sheet vinyl flooring is an affordable and versatile floor covering option. Because of vinyl's high level of moisture resistance and low maintenance requirements. · hey guys, my mother finds the ceramic in her new kitchen cold and hard- asked if i could put vinyl over it- preliminary research says no-.
Defects poking up through the vinyl may cause problems for the tile installation in the same way they do on other subsurfaces. Should I actually AVOID tiling over vinyl? Although it may seem intimidating or more risky than tiling over other surfaces, well adhered vinyl with the proper surface treatment to enhance bonding, will work well and may even resist limited horizontal movement. I still don't recommend it. So What's The Final Answer On Vinyl? Be sure and stay with your product manufacturer’s recommendations. Be sure and check with the mortar manufacturer for their specific installation advice. Installing tile over vinyl is relatively common these days, most of the manufactures do have products specifically designed to bond tile to vinyl. I still don't recommend it ". Installing Ceramic Tile Over Different Floor Surfaces. If you are installing ceramic tile over another surface, you need to follow specific recommendations and steps to make sure there will be proper bonding. Ceramic tile over wood, tile, concrete or vinyl should be installed by using certain products that will allow the right adhesion between surfaces. Always be sure that the existing surface has been cleaned and leveled. How to Install Ceramic Tile Over Concrete. Installing ceramic tile over concrete requires repairing all cracks and voids prior to the installation process. Fix all cracks with crack suppression products if cracks are small, or about 1/8 inch. If installing ceramic tile over larger cracks, you must consider removing the concrete section and pouring a new concrete slab. If you are concerned about cracks, you may want to have an isolation system installed onto the slab to separate/detach the tile from the slab. It is important to verify that there are no chemical products acting over the concrete surface. Chemical products applied over the concrete surface can reduce the bonding capacity of the tile over the surface. To check the slab for the presence of such a coating, drip a few drops of water on its surface. If the water beads, it's highly likely that a coating was applied. How to Install Ceramic Tile Over Wood. Installing ceramic tile over wood requires certain knowledge and the wood surface must be structurally sound to support the ceramic tile weight. Chip board, cushioned vinyl flooring, particle boards of any type, OSB (Oriented Strand Board), tongue and groove planking, and hardwood floors are unsuitable substrates to directly install ceramic tile over. Tile is hard and will break or dislodge if the surface bends under the load. If appropriate sand the wood surface to make it smoother. Remember that the installation will work better if it is being installed over an adequate subfloor and be at least 1 1/8" thick when combined with the subfloor. If the tile installation is going to be made in a bathroom, consider applying an isolation membrane over your wood subfloor, it will protect against expansion and contraction. Interior grade plywood and particle board are not materials capable of withstanding ceramic tile weight. How to Install Ceramic Tile Over Existing Tile. Before installing ceramic tile over existing tile you will need to roughen the existing ceramic tile surface to produce a rougher surface where the new ceramic will grip on to. It is recommended to sand the floor using 8. After the tile has been sanded, clean and remove all particles and dust, before applying a floor leveler product. The floor leveler product will fill in grout lines and level the surface completely for the new tile application. Use a thin- set to install ceramic tile over existing tiles. Consider that doors, cabinets, and other hardware might be reworked or replaced with new ones to compensate for the height reduction. Latex or epoxy type mortars are best for installing tile over tile. How to Install Ceramic Tile Over Existing Vinyl. Installing ceramic tile over existing vinyl could be more complicated than expected. Installing ceramic tile directly to vinyl or linoleum surfaces should be avoided whenever possible, however, if you decide to install follow these steps. First , you might want to remove the vinyl floor and its adhesive. If this is not possible, lay a backer board with thin- set and this will be your new subfloor material. It is important to use the recommended thin- set by the backer board manufacturer. Make sure all loose adhesive is removed from the surface and verify that a good bond to the substrate can be achieved. For cutback adhesive residue, verify that the thin- set manufacturer's mortar is compatible.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2017
Categories |